User Tools

Site Tools

Trace:
en:hems:methods_resources:commissioning

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
en:hems:methods_resources:commissioning [2020/08/11 13:33] – [Enable power-sensor from compatible systems] amra.begicen:hems:methods_resources:commissioning [2021/02/02 10:50] (current) – [Configuration] saso_santelj
Line 3: Line 3:
 ===== Mounting ===== ===== Mounting =====
  
-Mount the main controller MC-230, PM1-E-D, PM3-E-D and PM3-I-D electricity sensors, fuses, power relays and push-buttons to a suitable location.+Mount the main controller MC-230, PM1-E-D, PM3-E-D and PM3-I-D electricity sensors, fuses, power relays, and push-buttons to a suitable location.
  
 ===== Wiring ===== ===== Wiring =====
  
  
-Wire all elements **except** communication with single-phase **PM1-E-D sensors**.+Wire all elements **except** communication with **PM1-E-D** and **PM3-E-D sensors**.
  
 Connect the MC-230 to the home LAN. Connect the MC-230 to the home LAN.
Line 15: Line 15:
  
  
-Install and run {{ :hiq_energy:hems:methods_resources:hems_configurator_v1.1.1.exe|HEMS Configurator}} on your PC.+Install and run {{ :hiq_energy:hems:methods_resources:hems_configurator_v1.1.2.exe|HEMS Configurator}} on your PC.
  
 Go to the "**settings**" page. Go to the "**settings**" page.
Line 50: Line 50:
  
   * Make sure the "new device" is empty   * Make sure the "new device" is empty
-  * Press the button on power-sensor until **-Set-** appears on display+  * Press the button on power-sensor until **-Set-** appears on the display
   * In HEMS Configurator press **"del"** button next to the sensor   * In HEMS Configurator press **"del"** button next to the sensor
   * After a few seconds, the sensor should appear as the "new device"   * After a few seconds, the sensor should appear as the "new device"
Line 80: Line 80:
  
 === Wireless module adding === === Wireless module adding ===
 +
 +== Temperature and humidity sensor==
 +
 +   *Launch the pairing by the press on the learning button on the back of the device. 
 +   *The wireless sensor is added in the HEMS Configurator. 
  
 == Micro smart plug and Smart plug== == Micro smart plug and Smart plug==
Line 86: Line 91:
   * To confirm that the pairing is OK, the LED will blink in green   * To confirm that the pairing is OK, the LED will blink in green
   * In the HEMS Configurator module should appear as "new device"   * In the HEMS Configurator module should appear as "new device"
-  * Click on the **" add"** button next to the consumer that connected to the module+  * Click on the **" add"** button next to the consumer that is connected to the module
  
 == Relay switch-1 channel== == Relay switch-1 channel==
Line 93: Line 98:
   * To confirm that the pairing is OK, the LED will blink green twice   * To confirm that the pairing is OK, the LED will blink green twice
   * The HEMS Configurator module should appear as a "new device"   * The HEMS Configurator module should appear as a "new device"
-  * Click on the **" add"** button next to the consumer that connected to the module+  * Click on the **" add"** button next to the consumer that is connected to the module
  
 == Relay switch-2 channel== == Relay switch-2 channel==
Line 100: Line 105:
   * To confirm that the pairing is OK, the LED will blink green twice   * To confirm that the pairing is OK, the LED will blink green twice
   * In the HEMS Configurator the module first channel should appear as a "new device"   * In the HEMS Configurator the module first channel should appear as a "new device"
-  * Click on the **" add"** button next to the consumer that connected to the module first channel+  * Click on the **" add"** button next to the consumer that is connected to the modules first channel
   * In the HEMS Configurator the module second channel should appear as a "new device"    * In the HEMS Configurator the module second channel should appear as a "new device" 
-  * Click on the **" add"** button next to the consumer that connected to the module second channel+  * Click on the **" add"** button next to the consumer that is connected to the modules second channel
   * Before you pair a new device both channels must be added to the consumers   * Before you pair a new device both channels must be added to the consumers
  
Line 110: Line 115:
  
   * In the HEMS Configurator press **"del"** button next to the consumer connected to the module you want to remove   * In the HEMS Configurator press **"del"** button next to the consumer connected to the module you want to remove
-  * After a few seconds, the module is removing+  * After a few seconds the module is removed
  
 == Relay switch-2 channel== == Relay switch-2 channel==
  
   * In the HEMS Configurator press **"del"** button next to the consumer connected to the channel module you want to remove   * In the HEMS Configurator press **"del"** button next to the consumer connected to the channel module you want to remove
-  * After a few seconds, delete the channel of a module should appear as the "new device" +  * After a few seconds, deleted channel of a module should appear as a "new device" 
-  * If desired, the module can be removing if delete another channel or the deleted channel can be assigned to another consumer+  * We can remove the module by deleting the second channel or the deleted channel can be assigned to another consumer
  
 === Setting repeater level === === Setting repeater level ===
-When enabling repeater mode, the wireless module can repeater a message not addressed to him, and increase range by creating network gride between all wireless devices.+When enabling repeater mode, the wireless module can repeat a message not addressed to him, and increase range by creating network grid between all wireless devices.
  
 The repeater can be configured to level 0 (off), level 1 (one hop), or level 2 (two hops): The repeater can be configured to level 0 (off), level 1 (one hop), or level 2 (two hops):
Line 126: Line 131:
   ***Level 2**: gateway --- repeater --- repeater --- module².   ***Level 2**: gateway --- repeater --- repeater --- module².
  
-By default, the repeater mode is disabled (level 0). If you want to change the repeater mode press icon <<>> in the **output** in **Consumers settings table**.+By default, the repeater mode is disabled (level 0). If you want to change the repeater mode press icon **<<>>** in the **output** in **Consumers settings table**.
  
  
Line 159: Line 164:
 ==== Permanent memory ==== ==== Permanent memory ====
  
-Saving parameters to the permanent memory, after changing the settings, it is necessary since at startup HEMS always reads parameters from the permanent memory.+Saving parameters to the permanent memory, after changing the settings, is necessary since at startup HEMS always reads parameters from the permanent memory.
  
 ==== Backup / restore to PC ==== ==== Backup / restore to PC ====
  
-HEMS Configurator allows you to backup and restores all parameters to pc.+HEMS Configurator allows you to backup and restores all parameters to PC.
  
 ¹ Only for the first power plant ¹ Only for the first power plant
en/hems/methods_resources/commissioning.1597152809.txt.gz · Last modified: 2020/08/11 13:33 by amra.begic