User Tools

Site Tools

Trace: • faq
en:hems_v1_2_0:software

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
en:hems_v1_2_0:software [2021/11/16 14:05] – [io mux] gdzampoen:hems_v1_2_0:software [2021/11/30 09:16] (current) – [limiter] gdzampo
Line 262: Line 262:
 | Voltage for each phase                                                              ||| | Voltage for each phase                                                              |||
 ^ 5. Phase order                                                                      ||| ^ 5. Phase order                                                                      |||
-| Firstly set correct phase order for grid power sensor and then set for other powers sensors/devices. NOTE: changing grid phase order will NOT apply to phase order of other devices!       |||+| First set correct phase order for grid power sensor and then set for other power sensors/devices. NOTE: changing grid phase order will NOT apply to phase order of other connected devices!       |||
 ^ 6. Current limit                                                                    ||| ^ 6. Current limit                                                                    |||
 | Current limit threshold for main grid fuse                                          ||| | Current limit threshold for main grid fuse                                          |||
Line 277: Line 277:
  
 <WRAP clear></WRAP> <WRAP clear></WRAP>
- 
-<WRAP pagebreak></WRAP> 
  
 ===== ev fleet===== ===== ev fleet=====
Line 315: Line 313:
 <WRAP clear></WRAP> <WRAP clear></WRAP>
  
-<WRAP pagebreak></WRAP> 
  
 ===== io mux ===== ===== io mux =====
Line 332: Line 329:
 ^ 1. Select input/output type                                                         ||| ^ 1. Select input/output type                                                         |||
 | On the left side there are defined MC controller ([[en:hiq_hw:mc-230|MC-230]]) ports to which could be assigned MC-230 functions (digital, linker reset, router reset, etc). ||| | On the left side there are defined MC controller ([[en:hiq_hw:mc-230|MC-230]]) ports to which could be assigned MC-230 functions (digital, linker reset, router reset, etc). |||
-| Default settings are for e.g. QX0 -> digital 1 while digital 1 is defined for consumer 1 (settings page). It could be changed in a way to define new function to QX0 (linker reset) |||+| Default settings are for e.g. QX0 -> digital 1 while digital 1 is defined for consumer 1 (settings page). It could be changed in a way to define new function role to QX0 port e.g. for linker reset |||
 | If it is selected Enable consumer at input IX0,IX1 or IX2 it means that dedicated consumer will be managed (ON/OFF) by input signal on IX0,IX1 or IX2. For example, thermostat signal is wired to IXO port and via IO mux defined "Enable consumer 1" to IX0. While thermostat is active, it is consumer 1 active as well and vice versa.||| | If it is selected Enable consumer at input IX0,IX1 or IX2 it means that dedicated consumer will be managed (ON/OFF) by input signal on IX0,IX1 or IX2. For example, thermostat signal is wired to IXO port and via IO mux defined "Enable consumer 1" to IX0. While thermostat is active, it is consumer 1 active as well and vice versa.|||
 | Limitations: one temperature sensor is allowed, one consumer could be managed by one input only ||| | Limitations: one temperature sensor is allowed, one consumer could be managed by one input only |||
Line 342: Line 339:
  
 <WRAP clear></WRAP> <WRAP clear></WRAP>
- 
 <WRAP pagebreak></WRAP> <WRAP pagebreak></WRAP>
  
  
 ===== settings ===== ===== settings =====
- 
-Easy and intuitive system setup. 
- 
-<WRAP column 650px> 
  
 {{:hiq_energy:hems_v1_2_0:settings_1.png?direct&800|}} {{:hiq_energy:hems_v1_2_0:settings_1.png?direct&800|}}
  
-</WRAP> 
  
 <WRAP column 650px> <WRAP column 650px>
Line 369: Line 360:
 |  Virtual grid PS     | [] enable  | Check if system is without main grid power meter. Energy, power and currents are calculated from other power meters.                        | |  Virtual grid PS     | [] enable  | Check if system is without main grid power meter. Energy, power and currents are calculated from other power meters.                        |
 ^ 2. Modbus cycle time                                                                                                                                                 ||| ^ 2. Modbus cycle time                                                                                                                                                 |||
-|  Modbus cycle time   | Time in ms for modbus communication to complete reading of all connected devices.                                                                       ||+|  Modbus cycle time   | Grid power sensor refresh time in ms                                                                             ||
 ^ 3. Sources and Consumers settings table                                                                                                                                       ||| ^ 3. Sources and Consumers settings table                                                                                                                                       |||
 |      SOURCES             | Source name                                                                                                                                         || |      SOURCES             | Source name                                                                                                                                         ||
en/hems_v1_2_0/software.1637071503.txt.gz · Last modified: 2021/11/16 14:05 by gdzampo