Differences

This shows you the differences between two versions of the page.

--- en:ms_main:wiring [2020/05/15 19:43] – marjan_strnad
+++ en:ms_main:wiring [2020/11/15 16:47] (current) – marjan_strnad
@@ Line 1: / Line 1: @@
-====== Devices wiring ======
+====== LCS Devices wiring ======
@@ Line 8: / Line 8: @@
 Individual lights (or hard-wired light groups) are wired directly to the distribution box with an appropriate wire gauge (usually 3 × 1,5 mm<sup>2</sup>).
-Push-button flush boxes are wired directly to the distribution box with signal wires. One wire for each push-button and one common wire (for 3 push-buttons: 4 × 0,5 mm<sup>2</sup>). Push buttons that are controlling same light are connected to the same input in parallel.
+===== Push-button flush boxes are wired: =====
+- directly to the distribution box with signal wires. One wire for each push-button and one common wire (for 3 push-buttons: 4 × 0,5 mm<sup>2</sup>). Push buttons that are controlling same light are connected to the same input in parallel
-Sensors are wired directly to distribution box. More sensors can be used for same light. Presence sensors must be wired in **parallel**, read sensors in **series**.
+- directly to the distribution box with Cat5+ cable. Up to four buttons on one Cat5+ cable. One core wire for each push-button and one twisted pair for common (for 4 push-buttons: Cat 5+<sup>2</sup>). Push buttons that are controlling same light are connected to the same input in parallel.
+===== Motion sensors are wired: =====
+- directly to the distribution box with signal wires. One wire for each sensor and one common wire (for 3 push-buttons: 4 × 0,5 mm<sup>2</sup>). Sensors that are controlling same light are connected to the same input in parallel.
+- directly to the distribution box with Cat5+ cable. Up to four sensors on one Cat5+ cable. One core wire for each sensor, one twisted pair for +24 VDC power supply and one twisted pair for 0 VDC (ground) power supply  (for 4 sensors: Cat 5+<sup>2</sup>). Sensors that are controlling same light are connected to the same input in parallel.
+More sensors can be used for the same light.
 |< 60% 15% 85% >|
@@ Line 35: / Line 42: @@
 |< 60% 15% 85% >|
 ^ DALI Light                  | {{hiq_building_automation:hiq_home:methods:wiring:dali_light_wiring.png?nolink|}}       |
-<WRAP pagebreak></WRAP>
-===== Individually managed sockets =====
-{{hiq_building_automation:hiq_home:methods:wiring:individual_sockets.png?nolink&1000|}}
-Individual sockets are wired directly to the distribution box with an appropriate wire gauge (usually 3 × 2,5 mm<sup>2</sup>)
-Push-button flush boxes are wired directly to the distribution box with signal wires. One wire for each push-button and one common wire (for 3 push-buttons: 4 × 0,5 mm<sup>2</sup>)
-|< 60% 15% 85% >|
-^ Managed sockets                  | {{hiq_building_automation:hiq_home:methods:wiring:socket_wiring.png?|}}       |
-<WRAP pagebreak></WRAP>
-===== Group managed sockets =====
-{{hiq_building_automation:hiq_home:methods:wiring:group_sockets.png?nolink&1000|}}
-Sockets group is wired to the distribution box with an appropriate wire gauge (usually 3 × 2,5 mm<sup>2</sup>)
-Push-button flush boxes are wired directly to the distribution box with signal wires. One wire for each push-button and one common wire (for 3 push-buttons: 4 × 0,5 mm<sup>2</sup>)
-<WRAP pagebreak></WRAP>
-===== Blinds motors =====
-{{hiq_building_automation:hiq_home:methods:wiring:blinds.png?nolink&1000|}}
-Blind motors are wired directly to the distribution box with an appropriate wire gauge (usually 4 × 1,5 mm<sup>2</sup>)
-Push-button flush boxes are wired directly to the distribution box with signal wires. One wire for each push-button and one common wire (for 2 push-buttons (up/down): 3 × 0,5 mm<sup>2</sup>)
-|< 60% 15% 85% >|
-^ Blinds motor        | {{hiq_building_automation:hiq_home:methods:wiring:blinds_wiring.png?nolink|}}          |
-^ Blinds push-buttons | {{hiq_building_automation:hiq_home:methods:wiring:blinds_pb_wiring.png?nolink|}}       |
-<WRAP pagebreak></WRAP>
-===== Exhaust fan =====
-{{hiq_building_automation:hiq_home:methods:wiring:fans.png?nolink&1000|}}
-Exhaust fans are wired directly to the distribution box with an appropriate wire gauge (usually 3 × 1,5 mm<sup>2</sup>)
-Push-button flush boxes are wired directly to the distribution box with signal wires. One wire for each push-button and one common wire (for 1 push-button: 2 × 0,5 mm<sup>2</sup>)
-|< 60% 15% 85% >|
-^ Exhaust fan motor        | {{hiq_building_automation:hiq_home:methods:wiring:fans_wiring.png?nolink|}}          |
-<WRAP pagebreak></WRAP>
-===== HVAC =====
-{{hiq_building_automation:hiq_home:methods:wiring:hvac_wiring.png?nolink&1000|}}
-Radiator valves and boiler enable signal are wired directly to the distribution box with an appropriate wire gauge (usually 3 × 1,5 mm<sup>2</sup>)
-Thermostat is field module - see [[en:hiq_home:methods:wiring#Field modules|Field modules wiring]].
-|< 60% 15% 85% >|
-^ Radiator valve  | {{hiq_building_automation:hiq_home:methods:wiring:radiator_wiring.png?nolink|}}     |
 <WRAP pagebreak></WRAP>
@@ Line 115: / Line 56: @@
     * SC-4O-IQ
     * SC-4S-IQ
-  * HVAC controllers
-    * TH-1M-IQ
-    * TH-1T-IQ
-    * TH-2-IQ
-    * TH-3-IQ
-  * HVAC actuators
-    * FC-1-IQ
 |< 60% 15% 85% >|
@@ Line 135: / Line 69: @@
 ^ LED stripe    | {{hiq_building_automation:hiq_home:methods:wiring:led_rgb_wiring.png?nolink|!!    }}   |
-|< 60% 15% 85% >|
-^ Fan-Coil Fan    | {{hiq_building_automation:hiq_home:methods:wiring:fc-fan_wiring.png?nolink|}}     |
-^ Fan-Coil Valve  | {{hiq_building_automation:hiq_home:methods:wiring:fc-valve_wiring.png?nolink|}}     |