✎ en:hems_v1_2_0:wiring []

You've loaded an old revision of the document! If you save it, you will create a new version with this data.

====== HEMS v1.2.x wiring ======

|< 700px >|
^ MC-230                                                         |
|Wiring of default configuration. \\ NOTE: several different configurations can be configured with [[en:hems_v1_2_0:software|HEMS Configurator]].        |
|  {{ :hiq_energy:hems_v1_2_0:mc-230_terminals.png?direct |}}  |

|< 700px >|
^ IOT-L2-2                                                         |
|  {{ :hiq_energy:hems_v1_2_0:iot-l2-2_terminals.png?direct |}}  |

|< 700px >|
^ Network (LAN or LTE 4G modem) -> MC-230 and IOT-L2-2 \\ Optionally: \\  - PC with HEMS configurator \\  - PV inverter \\   - Hybrid inverter (battery storage system)   \\     - EV charger  \\ NOTE: When you change network configuration, MC-230 and IOT-L2-2 must be reset.      |
|Default connection to the LAN:                              |
|  {{ :hiq_energy:hems_v1_2_0:hems-linker01.png?direct |}}  |
|Optional LAN connections:                              |
|  {{ :hiq_energy:hems_v1_2_0:hems-linker02.png?direct |}}  |
|  {{ :hiq_energy:hems_v1_2_0:hems-linker03.png?direct |}}  |
| |
| |
|Default connection via LTE 4G modem:                            |
|**NOTE:** All connected devices will have internet access via LTE modem which can result in high costs on your LTE account. |
|  {{ :hiq_energy:hems_v1_2_0:hems-linker11.png?direct |}}  |
|Optional LTE 4G modem connection:                              |
|  {{ :hiq_energy:hems_v1_2_0:hems-linker12.png?direct |}}  |
| |
|**NOTE:** Specific network requirements, i.e. static IP address can be configured on the cloud service. Please contact [[http://support.robotina.com|support]]. |

|< 700px >|
^ PM3-I-D                                                       |
|  {{ :hiq_energy:hems:hardware:pm3_terminals.png?direct |}}     |

|< 700px >|
^ PM1-E-D                                                       |
|  {{ :hiq_energy:hems:hardware:pm1_terminals.png?direct |}}     |

|< 700px >|
^ PM1-E-D-CT      |
|  {{ :hiq_energy:hems:hardware:pm1_ct_terminals.png?direct |}}  |

|< 700px >|
^ PM3-E-D-CT      |
|  {{ :hiq_energy:hems:hardware:pm3_ct_terminals.png?direct |}}  |

|< 700px >|
^ WM-1      |
|  {{ :hiq_energy:hems:hardware:wm1_wiring.png?direct |}}  |

|< 700px >|
^ Power-sensors orientation     |
|  {{ :hiq_energy:hems:hardware:ps_orientation.png?direct |}}  |

|< 700px >|
^ Control consumer by external signal   |
|Connect external source to control device, e.g. thermostat signal on IX0 to control temperature by enabling/disabling connected device on QX0.|
|  {{ :hiq_energy:hems:hardware:water_heater_1.png?direct |}}  |

|< 700px >|
^ Set analog for consumer 1  |
|Connect analog device to IO14 for analog signal 0-10V or to IO15 for PWM signal (f=1kHz). Analog load is possible to set in configurator for consumer 1 only and reserved outputs are on IO14 & IO15.|
|  {{ :hiq_energy:hems:hardware:analog_1.png?direct |}}  |

Edit summary

Note: By editing this page you agree to license your content under the following license: CC Attribution-Share Alike 4.0 International