Page locked

This page is currently locked for editing by another user. You have to wait until this user finishes editing or the lock expires.
Currently locked by: 216.73.216.249,10.0.0.202
Lock expires at: 2025/06/04 04:05 (13 min)
This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== LCS Devices wiring ======


===== Discrete (on/off) & Dimmable lights =====

{{hiq_building_automation:hiq_home:methods:wiring:lights.png?nolink&1000|}}

Individual lights (or hard-wired light groups) are wired directly to the distribution box with an appropriate wire gauge (usually 3 × 1,5 mm<sup>2</sup>).

===== Push-button flush boxes are wired: =====
- directly to the distribution box with signal wires. One wire for each push-button and one common wire (for 3 push-buttons: 4 × 0,5 mm<sup>2</sup>). Push buttons that are controlling same light are connected to the same input in parallel

- directly to the distribution box with Cat5+ cable. Up to four buttons on one Cat5+ cable. One core wire for each push-button and one twisted pair for common (for 4 push-buttons: Cat 5+<sup>2</sup>). Push buttons that are controlling same light are connected to the same input in parallel.

Motion sensors are wired:

- directly to the distribution box with signal wires. One wire for each sensor and one common wire (for 3 push-buttons: 4 × 0,5 mm<sup>2</sup>). Sensors that are controlling same light are connected to the same input in parallel.

- directly to the distribution box with Cat5+ cable. Up to four sensors on one Cat5+ cable. One core wire for each sensor, one twisted pair for +24 VDC power supply and one twisted pair for 0 VDC (ground) power supply  (for 4 sensors: Cat 5+<sup>2</sup>). Sensors that are controlling same light are connected to the same input in parallel.
More sensors can be used for the same light.

|< 60% 15% 85% >|
^ Light                        | {{hiq_building_automation:hiq_home:methods:wiring:light_wiring.png?nolink|}}       |
^ Dimmable light               | {{hiq_building_automation:hiq_home:methods:wiring:dimm_light_wiring.png?nolink|}}  |
^ Push-button                  | {{hiq_building_automation:hiq_home:methods:wiring:pushbutton_wiring.png?nolink|}}  |
^ Door / window \\ reed sensor | {{hiq_building_automation:hiq_home:methods:wiring:reed_wiring.png?nolink|}}        |
^ PIR motion sensor            | {{:en:ms_main:motion_sensor_wiring.png?600|}}        |
^ Light sensor                 | {{hiq_building_automation:hiq_home:methods:wiring:sensor_wiring.png?nolink|}}      |
 
<WRAP pagebreak></WRAP>

===== DALI dimmable lights =====

{{hiq_building_automation:hiq_home:methods:wiring:dali_lights.png?nolink&1000|}}

All light ballasts are wired to DALI bus with an appropriate wire gauge (usually 5 × 1,5 mm<sup>2</sup>)

Push-button flush boxes are wired directly to the distribution box with signal wires. One wire for each push-button and one common wire (for 3 push-buttons: 4 × 0,5 mm<sup>2</sup>)

Sensors are wired directly to the distribution box. More sensors can be used for the same light. Presence sensors must be wired in **parallel**, read sensors in **series**.


|< 60% 15% 85% >|
^ DALI Light                  | {{hiq_building_automation:hiq_home:methods:wiring:dali_light_wiring.png?nolink|}}       |

<WRAP pagebreak></WRAP>

===== Field modules =====

{{hiq_building_automation:hiq_home:methods:wiring:field_modules.png?nolink&1000|}}

Applies to:
  * Light controller
    * LD-V4-IQ
  * Scene controllers 
    * SC-4T-IQ
    * SC-4O-IQ
    * SC-4S-IQ

|< 60% 15% 85% >|
^ IEX2 bus  | {{hiq_building_automation:hiq_home:methods:wiring:iex2_wiring.png?nolink|}}     |

All field modules are connected to the IEX bus with 2 x 2 x 0,8 mm<sup>2</sup> cable.

Some devices controlled by Field modules needs additional power supply:
  * LD-V4-IQ need LED power supply; 12 or 24V DC depending of LED stripe type
  * FC-1-IQ need fan-coil motor and valve power supply; see fan-coil documentation - usually 230V AC

|< 60% 15% 85% >|
^ LED stripe    | {{hiq_building_automation:hiq_home:methods:wiring:led_rgb_wiring.png?nolink|!!    }}   |