GOFLEX HEMS wiring

Control distribution-board wiring

Control system and Communication interfaces wiring

PS-IQ	DIN rail

L, N	to 230 VAC power supply
+, -	to HC-IQ 24V, 0V (1, 2)
+, -	to GW-WN-W +, -

HC-IQ	DIN rail
24V (1), 0V (2)	to PS-IQ +, -
C0 (4), C1 (10)	Power relays supply
QX0-QX7 (5-9, 11-13)	Managed loads power relays
24V (19)	to HC-IQ C3 (22)
0V (20)	to push-buttons common
IX1-IX7 (23-29)	to push-button
RJ10 (right side)	to next DIN rail module

CAD-232-A2-IQ	DIN rail
A (1), B (2), C (3)	RS485 bus to power-meters and to GW-WN-IQ
RJ10 (left side)	to previous DIN rail module
RJ10 (right side)	to next DIN rail module

CAD-BE-PROT-IQ	DIN rail
GND (1), CANL (2), CANH (3), +24V (4)	IEX2 bus to field modules
RJ10 (left side)	to previous DIN rail module
RJ10 (right side)	to next DIN rail module

AIR-12-IQ	DIN rail
IWx , C	Pt 1000 temperature probe
RJ10 (left side)	to previous DIN rail module
RJ10 (right side)	to next DIN rail module

GW-ENO-IQ	DIN rail
RJ10 (left side)	to previous DIN rail module
RJ10 (right side)	to next DIN rail module

GW-WN-W	on wall

+, -	to PS-IQ +, -
Rx/T+, Tx/T-	to CAD-232-A2-IQ A, B
DIP settings	1=ON, 2-8=OFF

Sources and consumers measurements

PM3-I-D	DIN rail

L1i, L2i, L3i, N	to power source L1, L2, L3, N (grid, local power plant, generator, …)
L1o, L2o, L3o, N	to consumers L1, L2, L3, N
15, 16	to CAD-232-A2-IQ A,B or to BR-WN-W Rx/T+, Tx/T- when there is no possibility to connect directly

PM1-E-D	DIN rail
L↑ (1)	to power source L (grid, local power plant, generator, …)
L↓ (2)	to consumer L
9, 10	to CAD-232-A2-IQ B,A or to BR-WN-W Tx/T-, Rx/T+ when there is no possibility to connect directly

BR-WN-W	on wall

+, -	to Plug-in power supply +, - (included in the delivery)
Rx/T+, Tx/T-	to PM1-E-D 10, 9 ot to PM3-I-D 15,16
DIP settings	ALL OFF

Power-relays	DIN rail

Relays control voltage A1, A2	HC-IQ-HEMS QX0-QX7 for managed load 1 to 8, N
(2, 4 or 2, 4, 6, R8)	Consumer power supply L, N or L1, L2, L3, N
(1, 3 or 1, 3, 5, R7)	Consumer L, N or L1, L2, L3, N


PM1-WN-D	DIN rail
16, 17	power supply 230 VAC
2, 3	current transformer black, red
6, 7	consumer power supply - consumer L


PM1-WN-W	on wall
1, 1a	PE, internally connected
2, 2a	N, internally connected
3	Device supply / Current transformer black
3a	Current transformer red
3b	Output (Consumer)


RL1-WN-W	on wall
1, 1a	PE, internally connected
2, 2a	N, internally connected
3	Device and consumer supply
3a	Consumer output

SC1-WN-F	power outlet
Plugged in power outlet, consumer plugged in

TS-H	on wall

GND, CANL, CANH, +24V	BE-PROT-IQ GND, CANL, CANH, +24V
TS0, GND	ES external temperature probe red, black


AIR-12	DIN rail
C, IW0-IW11	Pt1000 temperature probes
RJ10 (left side)	to previous DIN rail module
RJ10 (right side)	to next DIN rail module


TDI-WN-W	on wall
1, 2 (from top)	Digital input 1
3, 4	Digital input 2
5, 6	NTC temperature probe input 1
7, 8	NTC temperature probe input 2
+, -	Plug-in power supply
DIP setting	Address setting: [1=lsb, 8=msb]
	- sensor 1, address 60 = 0011 1100
	- sensor 2, address 61 = 1011 1100
	- sensor 3, address 62 = 0111 1100
	- sensor 4, address 63 = 1111 1100
	- sensor 5, address 64 = 0000 0010
	- sensor 6, address 65 = 1000 0010
	- sensor 7, address 66 = 0100 0010
	- sensor 8, address 67 = 1100 0010