Differences

This shows you the differences between two versions of the page.

--- en:hems_v1_2_0:methods_resources:wiring [2021/11/05 15:03] – saso_santelj
+++ en:hems_v1_2_0:methods_resources:wiring [2021/11/12 08:53] (current) – removed saso_santelj
@@ Line 1: / Line 1: @@
-====== HEMS v1.2.x wiring ======
-|< 700px >|
-^ MC-230                                                         |
-|Wiring of default configuration. \\ NOTE: several different configurations can be configured with [[en:hems_v1_2_0:software|HEMS Configurator]].        |
-|  {{ :hiq_energy:hems_v1_2_0:mc-230_terminals.png?direct |}}  |
-<WRAP pagebreak></WRAP>
-|< 700px >|
-^ IOT-L2-2                                                         |
-|  {{ :hiq_energy:hems_v1_2_0:iot-l2-2_terminals.png?direct |}}  |
-<WRAP pagebreak></WRAP>
-|< 700px >|
-^ Network -> MC-230, IOT-L2-2 and optionally LTE 4G modem        |
-|Default connection to the LAN:                              |
-|  {{ :hiq_energy:hems_v1_2_0:hems-linker01.png?direct |}}  |
-|Optional LAN connections:                              |
-|  {{ :hiq_energy:hems_v1_2_0:hems-linker02.png?direct |}}  |
-|  {{ :hiq_energy:hems_v1_2_0:hems-linker03.png?direct |}}  |
-| |
-|Default connection via LTE 4G modem:                            |
-|  {{ :hiq_energy:hems_v1_2_0:hems-linker11.png?direct |}}  |
-|Optional LTE 4G modem connection:                              |
-|  {{ :hiq_energy:hems_v1_2_0:hems-linker12.png?direct |}}  |
-| |
-|NOTE: optional connection has to be configured on the cloud service. Please contact [[http://support.robotina.com|support]]. \\ The same applies to specific network requirements, i.e. static IP address. |
-<WRAP pagebreak></WRAP>
-|< 700px >|
-^ PM3-I-D                                                       |
-|  {{ :hiq_energy:hems:hardware:pm3_terminals.png?direct |}}     |
-<WRAP pagebreak></WRAP>
-|< 700px >|
-^ PM1-E-D                                                       |
-|  {{ :hiq_energy:hems:hardware:pm1_terminals.png?direct |}}     |
-<WRAP pagebreak></WRAP>
-|< 700px >|
-^ PM1-E-D-CT      |
-|  {{ :hiq_energy:hems:hardware:pm1_ct_terminals.png?direct |}}  |
-<WRAP pagebreak></WRAP>
-|< 700px >|
-^ PM3-E-D-CT      |
-|  {{ :hiq_energy:hems:hardware:pm3_ct_terminals.png?direct |}}  |
-<WRAP pagebreak></WRAP>
-|< 700px >|
-^ WM-1      |
-|  {{ :hiq_energy:hems:hardware:wm1_wiring.png?direct |}}  |
-<WRAP pagebreak></WRAP>
-|< 700px >|
-^ Power-sensors orientation     |
-|  {{ :hiq_energy:hems:hardware:ps_orientation.png?direct |}}  |
-<WRAP pagebreak></WRAP>
-|< 700px >|
-^ Control consumer by external signal   |
-|Connect external source to control device, e.g. thermostat signal on IX0 to control temperature by enabling/disabling connected device on QX0.|
-|  {{ :hiq_energy:hems:hardware:water_heater_1.png?direct |}}  |